Provic S3 VV Mod 3V-6V Kit.
Package includes
-
1 x JOYELIFE provic mod
-
1 x clearomizer
-
1 x charging adapter
Main Functions:
1. Battery spec
1) Provic S3 works with 18650lithium-ion battery.
2) Recharge: take out thelithium-ion battery and recharge with dedicated charger till it’s full charged.
2. Working parameters
1) Resistance >0.8ohm atomizer is recommended
2) Quiescent current: <100uA
3) With RMS and average voltage outputfunction, voltage output error is ±0.1V
3. Basic functions
1). Power on: OLED shows “JOYELIFE”, Vibration motorshake one time and enter the key lock status.
2). Limited time protection: When smoking timeexceeds the setting time ,output will be forced to be shut down.
3). The OLED screen will show “Please ChangeBattery”while the voltage is below 3.4v, it means the voltage is too low to besmoking, the device need to be recharged.
4.Features
1. RMS and Mean average voltage output: Outputvoltage is 3.0v-6.0v and error is ±0.1V, Automatically match the atomizer resistanceand to achieve the same amount of smoking.
2. Button/Knob: 31 voltages can be adjusted.
3. Resistance measurement function: Test theactual resistance of atomizer.
4. Display functions: Display the currentbattery level, voltage output, atomizer resistance, puffs, remaining puffs andsmoking timeout.
5. Reverse battery protection function: Control Board will start protection function to protect the Components and battery in case of the battery reversed.
6. Low voltage alarm: the OLED will alarm while the voltage is low 3.4V to protect thebattery.
5.Operation Method
1. Lockbutton: in the locked position, press 5 times ina row to unlock, the OLED will display JOYELIFE and start the normal working status.In normal workingconditions, press 5 times to lock. It can not be smoke in lock status.
2. Voltage increases: In the voltage display interface, turn around the buttonclockwise, the voltage adjusts from 3.0V to6.0V in 0.1v increments.
3. Voltage decrease: In the voltage display interface, turn around the buttonanticlockwise, the voltage adjusts from6.0V to 3.0V in 0.1v decrease.
4. Setup menu: In sleep mod status or voltage display, press thebutton 3 times in a row will enter setup mode, rotate the encoder to select,then press the button.
5. Puff info: To enter the Setup mode, turn around the encoder toselect “Puff info” then press the button to set the puff info.
5.1) To enter the submenu of the set puff, turn around theencoder to select the “Set puff”, then press the button to set the puffs.When the cursor blinks, turn around the encoder to movethe cursor, or press the button to fix the cursor and setting thenumeral value that from 0001-9999 puffs what the user want. after settingsuccessfully, select Exit to exit submenu and return to the previous menu.
5.2) Reset puff: to enter the submenu of the set puff, thenpress the button to select the “Reset the puffs”to clear the puffs.
5.3) To enter the submenu of the set puff, turn around theencoder to select the“Total puff” to show the total puff being smoked.
5.4) Puff time: to enter the submenu of the set puff, turnaround the encoder to select the puff time 6s~30s.
6. Lock timeIn the setting mode, turn around the encoder and selectthe lock time for 30 Mins/60 Mins/Never. After setting successfully, select Exit to exit submenu and return to the previous menu.
7. VibrationIn the setting mode, turn around the encoder and select vibration for setting the vibration of motor or on/off. after setting successfully, select Exit to exit submenu and return to the previous menu.
8. MobileIn the setting mode, turn around the encoder and selectthe power bank mode or on/off. after setting successfully, select Exit to exitsubmenu and return to the previous menu. When the device is on mobile powersupply mode, it can not be used for smoking but only for recharging for otherdevices, and the output voltage is around 6v, the device will exit the mobileon while low voltage of battery or the resistance is lower than 5ohms.
9. ScreenIn the setting mode, turn around the encoder and selectthe screen to setting the light time of OLED , options 5 sec/10 sec/30 sec/60sect. after setting successfully, select Exit to exit submenu and return to theprevious menu.
10. Output In the setting mode, turn around the encoder and selectthe output for setting output.Turn about the encoder again and press the button forsetting the output mode options RMS/Mean/. After setting successfully, select Exitto exit submenu and return to the previous menu.
11. My deviceIn the setting mode, turn around the encoder and select “Mydevice” for setting the device info. Turn around the encoder again and pressand the button for setting the info of name/user info/ohm, after settingsuccessfully, select Exit to exit submenu and return to the previous menu.
12. SleepIn the setting mode, turn around theencoder and select the Sleep, device will quit setting menu for sleep.
13. ExitIn the setting mode, turn around theencoder and select Exit to exit the setting mode of the device.
14.Short circuit protectionThe screen will display atomizer short in case of short circuit at the output in smoking mode or mobile power supply mode. You have tocheck the electrode carefully for both atomizer and battery body.
15. Low load protectionScreen will display low resistance whilethe output resistance is lower than 1.2ohmin smoking mode or lower than 5ohm in the mobile power supplymode, and the device will exit output automatically.
Welcome to our store!
.jpg)
.jpg)
